Warenkorb anzeigen (0 Artikel) Mein KontoMerkzettel anzeigenZur Kasse gehen

Alja-Safe™ Acrobat™

Alja-Safe™ Acrobat™ ist eine faserverstärkte "non-sag" Version des originalen Alja-Safe™ Life Casting Alginats. Alja-Safe™ Acrobat™ ist dicker und hält vertikale Oberflächen, so dass der Benutzer eine bessere Kontrolle bei der Herstellung von Gesichts-, Rumpf- usw hochdetaillierte Reproduktionen, die in Wachs, Gips, Matrix™ NEO™ (polymermodifizierter Gips), platinhärtendes Silikon oder Smooth-Cast™ 300Q ultraschnelles Urethanharz gegossen wurden.

Einfach zu verwenden – Das Mischungsverhältnis beträgt 1 Teil Alja-Safe™ Acrobat™ Pulver, gesiebt in 1 Teil Wasser (1:1 nach Volumen). Die Verarbeitungszeit beträgt 5 Minuten und die Aushärtezeit 8 Minuten bei einer Wassertemperatur von 27°C.

Wie Original Alja-Safe™ ist Alja-Safe™ Acrobat™ hautverträglich und enthält keine kristalline Kieselsäure (ein bekanntes Karzinogen).

Um wiederverwendbare Formen von Körperteilen herzustellen, verwenden Sie Body Double™ Silikonkautschuk.

Wichtig - Dieses Produkt wurde nicht getestet und sollte nicht für zahnärztliche Anwendungen verwendet werden.

Alja-Safe™ Acrobat

  • Alja-Safe™ Acrobat™ /1,36 kg

    fiber reinforced version of Alja-Safe. Alja-Safe™ Acrobat™ is thicker and holds vertical surfaces for more control to make molds of the face, torso, etc.

    34,50 EUR (zzgl. 21% USt. zzgl. Versand)

  • Alja-Safe™ Acrobat™ / 9 kg

    fiber reinforced version of Alja-Safe. Acrobat is thicker and holds vertical surfaces for more control to make molds of the face, torso, etc.

    208,40 EUR (zzgl. 21% USt. zzgl. Versand)

  • Alja-Safe™ Acrobat™ /22,7 kg

    fiber reinforced version of Alja-Safe. Acrobat is thicker and holds vertical surfaces for more control to make molds of the face, torso, etc.

    437,22 EUR (zzgl. 21% USt. zzgl. Versand)

Instructions:

Preparation -
Store and use Alja-Safe™ Acrobat™ in a dry environment at room temperature. Alja-Safe™ Acrobat™ powder may get warm in storage/shipping during the summer months which will cause the powder/water mixture to set too fast. To remedy, store Alja-Safe™ Acrobat™ in a cool area 15° C - 31° C for 24 hours before using. Alja-Safe™ Acrobat™ has a limited shelf life and should be used as soon as possible. Do not allow moisture to come into contact with unused Alja-Safe™ Acrobat™. Use only with adequate ventilation.

Make a mold of the back of your hand – make a mold of something small before going on to larger models. You’ll gain a lot of experience with a small test.

Applying A Release Agent – Alja-Safe™ Acrobat™ will not stick to most surfaces. When making a mold of the head, a release preparation is recommended to prevent mechanical lock to the hair. Cholesterol based hair conditioner (available at most pharmacies) can be applied to hair-covered areas prior to applying Alja-Safe™ Acrobat™. It can be washed out of the hair easily after use.

Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.

Measuring – Alja-Safe™ Acrobat™ is mixed 1 part water to 1 part powder by volume (1 cup + 1 cup, for example).

Important - You must pack the powder firmly into the measuring cup. You can vary the water level somewhat to change consistency of the mixture. Less water will make Alja-Safe™ Acrobat™ thicker. More water will make the mixture thinner. Be careful…too much water will may result in the mixture not curing.

Water Quality – Water that has a high mineral content (calcium, phosphate, etc.) may cause any alginate to become "lumpy" or not set properly. A small-scale test is recommended prior to mixing large amounts.

Temperature Of The Water - At 27° C, Alja-Safe™ Acrobat™ will have a working time of 8 minutes and a demold time of 10 minutes. Warmer water will cause the material to cure faster (less working time). Colder water will give a longer working time and slower demold time. For best results, sift Alja-Safe™ powder into water and mix as directed.

Mixing – Alja-Safe™ Acrobat™ can be hand mixed, but best results will be obtained using a power drill with a mixer attachment. Attach a Jiffy Mixer or Turbine Mixer to a power drill and mix for one minute (depending on volume) to a gel-like consistency – smooth without any powder lumps. Jiffy mixers are available at many hardware stores. Turbine Mixers will yield the best mix and are available here at Form X

Alja-Safe™ Acrobat™ is designed to be applied to vertical surfaces.

For Best Results - Wet the surface of the model’s skin before applying. Apply a thin coating of Alja-Safe™ Acrobat™ to the surface of the model by brushing, smoothing the material on by hand or using a plastic spatula. Keep your model still until the Alja-Safe™ Acrobat™ sets up. You will know the Alja-Safe™ Acrobat™ has set when it is firm and no longer gel-like.

You may want to experiment with the amount of water added to Alja-Safe™ Acrobat™ to find a thicker consistency that is right for vertical surface application. For example, some customers mix 1 part water to 1.5 parts Alja-Safe™ Acrobat™.

Applying A Support Shell - Once the material cures, a support shell will be necessary to support the Alja-Safe™ Acrobat™ mold. Gypsona brand medical grade plaster bandages are ideal for this purpose, and are available here at Form X

Casting Into The Mold - All alginate molds will deteriorate quickly. It is recommended that you cast into the mold within 4 hours following demold. Materials commonly cast into alginates include Matrix NEO (polymer modified gypsum, available here at Form X), plaster, wax, clay and very fast urethane resins (such as Smooth-Cast™ 300Q). For Soft "Skin-Like" Castings – You can cast Dragon Skin™ FX Pro™ soft silicone rubber into Alja-Safe™ Acrobat™ molds to make realistic hands, limbs, etc.

Hilfe bei der Auswahl

Produkte nach Anwendung sortiert, z. B.:Lifecasting, Bildhauerei, Gießen, Special FX Make-up, Zahnprothesen Special FX, Studium.

Über uns Kontakt Transportoptionen Kundenprojekte Anwendungsbereich Branches

Ihr One-Stop-Shop für 3D-Modelling-Materialien