Warenkorb anzeigen (0 Artikel) Mein KontoMerkzettel anzeigenZur Kasse gehen

VytaFlex Serie

Vytaflex Serie

Die VytaFlex Serien ist die neueste Entwicklung in den Smooth-On PU-Kautschuken. Mit dem 1A: 1B Mischungsverhältnis bieten sie eine einfache Verarbeitungweise aber eine höhere Festigkeit, Haltbarkeit und ist ein "High-Performance" Kautschuk durch das einzigartige V-Polymer. Diese spezielle Formulierung, die beim Vernetzungsprozess eine dichtere Zellstruktur und dadurch eine glattere Oberfläche der Negativform ergibt, ermöglicht bessere Trenneigenschaften und den sparsamen Einsatz von Betonschalölen. Auf Grund der geringeren Rückstände in der PU-Negativform, werden sowohl einheitlichere als auch farbgetreuere Betongüsse erzielt. Die VytaFlex Kautschuke funktionieren also besonders gut mit pigmentierten Beton oder Putz. Weil sie nicht den Farbstoffstaub aus Beton absorbieren, übertragen sie keine Farbrückstände zum nächsten Casting. Die VytaFlex Formen lieferen mit jedem Casting detailliert und farbgetreue Gussteile.

Die Vytaflex Kautschuke sind in Härten Shore A10 - A20 - A30 - A40 - A50 und A60 lieferbar.

Vytaflex 20 ist transparent und nahezu farblos und wird häufig für dekorative und Spezialeffekt-Anwendungen verwendet.

Technical Bulletin

  • VF 10
  • VF 20
  • VF 30
  • VF 40
  • VF 50
  • VF 60
  • Table
  • Instructions

VF10

- hardheid: Shore A10
- kleur: beige

VytaFlex 10

  • VytaFlex 10 /1kg

    Gießbarer Polyurethankautschuk, Shore-Härte von A10, Set von 0,94 kg

    22,60 EUR (zzgl. 21% USt. zzgl. Versand)

  • VytaFlex 10 /7kg

    Gießbarer Polyurethankautschuk, Shore-Härte von A10, Set von 7,2 kilo

    133,30 EUR (zzgl. 21% USt. zzgl. Versand)

VF20

- hardheid: Shore A20
- kleur: bijna kleurloos transparant

VytaFlex 20

  • Vytaflex 20 /1kg

    Gießbarer Polyurethankautschuk, Shore-Härte von A20, Set von 0,94 kg

    22,60 EUR (zzgl. 21% USt. zzgl. Versand)

  • Vytaflex 20 /7kg

    Gießbarer Polyurethankautschuk, Shore-Härte von A20, Set von 7,2 kg

    133,30 EUR (zzgl. 21% USt. zzgl. Versand)

  • Vytaflex 20 /36,2 kg

    Vytaflex 20, 5 Gallon Unit, Shore A20 pourable P.U. rubber.Set 36,2 kgs.

    546,45 EUR (zzgl. 21% USt. zzgl. Versand)

VytaFlex 30

  • Vytaflex 30 /1kg

    Gießbarer Polyurethankautschuk, Shore-Härte von A30, Set von 0,94 kg

    22,60 EUR (zzgl. 21% USt. zzgl. Versand)

  • VytaFlex 30 /7,2kg

    Gießbarer Polyurethankautschuk, Shore-Härte von A30, Set von 7,2 kg

    133,30 EUR (zzgl. 21% USt. zzgl. Versand)

Features

- Hardness: Shore A 30
- Elongation at Break: 1000 %
- Tensile Strength: 13.9 N/mm
- Colour: Beige

VytaFlex 40

  • Vytaflex 40 /1kg

    Gießbarer Polyurethankautschuk, Shore-Härte von A40, Set von 94 kg

    22,60 EUR (zzgl. 21% USt. zzgl. Versand)

  • VytaFlex 40 /7,2kg

    Gießbarer Polyurethankautschuk, Shore-Härte von A40, Set von 7,2 kg

    133,30 EUR (zzgl. 21% USt. zzgl. Versand)

  • VytaFlex 40 /36,2kg

    Gießbarer Polyurethankautschuk, Shore-Härte von A40, Set von 36,2 kg

    562,95 EUR (zzgl. 21% USt. zzgl. Versand)

Features

- Hardness: Shore A 30
- Elongation at Break: 1000 %
- Tensile Strength: 13.9 N/mm
- Colour: Beige

VytaFlex 50

  • Vytaflex 50 /1kg

    Gießbarer Polyurethankautschuk, Shore-Härte von A50, Set von 0,94 kg

    22,45 EUR (zzgl. 21% USt. zzgl. Versand)

  • VytaFlex 50 /7,2kg

    Gießbarer Polyurethankautschuk, Shore-Härte von A50, Set von 7,2 kg

    142,70 EUR (zzgl. 21% USt. zzgl. Versand)

VytaFlex 60

  • Vytaflex 60 /1kg

    Gießbarer Polyurethankautschuk, Shore-Härte von A60, Set von 0,94 kg

    22,45 EUR (zzgl. 21% USt. zzgl. Versand)

  • Vytaflex 60 /7,2kg

    Gießbarer Polyurethankautschuk, Shore-Härte von A60, Set von 7,2 kg

    142,70 EUR (zzgl. 21% USt. zzgl. Versand)

  • Vytaflex 60 /36,2 kg

    Met behulp van Smooth-On's exclusieve "V-Polymer" technologie, bieden VytaFlex ® urethaanrubbers superieure fysieke en prestatie-eigenschappen. VytaFlex ® urethanen hebben een handige een op een (vol ...

    601,40 EUR (zzgl. 21% USt. zzgl. Versand)

Vytaflex Table

VYTAFLEX® Mixture (by Volume) Mixed Viscosity (mPas) Specific Weight(g/cm³) Pot Life (min) Cure Time (hrs) Colour Hardness (Shore A) Tensile Strength (N/mm) Elongation at Break (%) Schrinkage (%)
10 1A:1B 3100 1,00 30 24 creme 10 6,8 1000 <0,1
20 1A:1B 1000 1,00 30 16 amberclear 20 10,7 1000 <0,1
30 1A:1B 1800 1,02 30 16 creme 30 13,9 1000 <0,1
40 1A:1B 2000 1,03 30 16 creme 40 14,6 660 <0,1
50 1A:1B 2000 1,04 60 16 creme 50 18,2 400 <0,1
60 1A:1B 2000 1,04 60 16 creme 60 24,3 480 <0,1

Preparation - Store and use at room temperature (73°F/23°C). These products have a limited shelf life and should be used as soon as possible. Environmental humidity should be as low as possible. Good ventilation (room size) is essential. Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk.

Some Materials Must Be Sealed - Urethanes are adhesive. To prevent adhesion between the rubber and model surface, models made of porous materials (gypsum plasters, concrete, wood, stone, etc.) must be sealed prior to applying a release agent. SuperSeal® (available from Smooth-On) or One Step® are fast drying sealers suitable for sealing porous surfaces without interfering with surface detail. Sonite Wax®or high-grade shellac is suitable for rough contours. A high quality Shellac is suitable for sealing modeling clays that contain sulfur or moisture (water based). Thermoplastics (polystyrene) must also be sealed with shellac or PVA. In all cases, the sealing agent should be applied and allowed to completely dry prior to applying a release agent.

Non-Porous Surfaces - Metal, glass, hard plastics, sulfur free clays, etc. require only a release agent.

IMPORTANT: Shelf life of product is reduced after opening. Remaining product should be used as soon as possible. Immediately replacing the lids on both containers after dispensing product will help prolong the shelf life of the unused product. XTEND-IT® Dry Gas Blanket (available from Smooth-On) will significantly prolong the shelf life of unused liquid urethane products.

Applying A Release Agent - A release agent is necessary to facilitate demolding when casting into or over most surfaces. Use a release agent made specifically for mold making (Universal® Mold Release available from Smooth-On). A liberal coat of release agent should be applied onto all surfaces that will contact the rubber.

IMPORTANT: To ensure thorough coverage, lightly brush the release agent with a soft brush over all surfaces of the model. Follow with a light mist coating and let the release agent dry for 30 minutes. Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.

MEASURING & MIXING - Liquid urethanes are moisture sensitive and will absorb atmospheric moisture. Mixing tools and containers should be clean and made of metal or plastic. Materials should be stored and used in a warm environment (73°F/23°C).

IMPORTANT: Pre Mix the Part B before using. After dispensing equal amounts of Parts A and B into mixing container, mix thoroughly for at least 3 minutes making sure that you scrape the sides and bottom of the mixing container several times.

If Mixing Large Quantities (16 lbs./7 kgs. or more) at one time, use a mechanical mixer (i.e. Squirrel Mixer or equal) for 3 minutes followed by careful hand mixing for one minute as directed above. Then, pour entire quantity into a new, clean mixing container and do it all over again.

Although this product is formulated to minimize air bubbles in your the cured rubber, vacuum degassing prior to pouring rubber will further reduce entrapped air.

POURING, CURING & PERFORMANCE - For best results, pour your mixture in a single spot at the lowest point of the containment field. Let the rubber seek its level up and over the model. A uniform flow will help minimize entrapped air. The liquid rubber should level off at least 1/2” (1.3 cm) over the highest point of the model surface.

Curing - Allow rubber to cure a minimum of 16 – 24 hours at room temperature (73°F/23°C) before demolding. VytaFlex® 10 should cure for at least 24 hours before demolding. Cure time can be reduced with mild heat or by adding Smooth-On “KickIt®” Cure Accelerator. Do not cure rubber where temperature is less than 65°F/18°C.

Post Curing - Optional . . . Following an overnight cure, heating the rubber to 150°F (65°C) for 4 to 8 hours will increase physical properties and performance.

Using The Mold - If using as a mold material, a release agent should be applied to the mold before each casting. In & Out® II Concrete Release Concentrate (available from Smooth-On) is recommended for releasing concrete.

Performance & Storage - Fully cured rubber is tough, durable and will perform if properly used and stored. The physical life of the rubber depends on how you use it.

  • ++
  • Pinsel
  • Schutzkleidung

Pinsel

  • flat brush 30mm

    flache Einwegbürsten - 30 mm - pro Stück

    0,85 EUR (zzgl. 21% USt. zzgl. Versand)

  • flat brush 40mm

    flache Einwegbürsten - 40 mm - pro Stück

    0,95 EUR (zzgl. 21% USt. zzgl. Versand)

  • flat brush 50mm

    flache Einwegbürsten - 50 mm - pro Stück

    1,15 EUR (zzgl. 21% USt. zzgl. Versand)

  • flat brush 60mm

    flache Einwegbürsten - 60 mm - pro Stück

    1,45 EUR (zzgl. 21% USt. zzgl. Versand)

  • flat brush 70mm

    flache Einwegbürsten - 70 mm - pro Stück

    1,55 EUR (zzgl. 21% USt. zzgl. Versand)

  • Calupaint Platte kwast Super Prof gelakte houten s

    Calupaint Platte kwast Super Prof gelakte houten s

    2,15 EUR (zzgl. 21% USt. zzgl. Versand)

  • polyesterkwast 20mm rond, houten steel, ongelakt

    polyester brush 20mm round, wooden handle, unvarnished

    2,55 EUR (zzgl. 21% USt. zzgl. Versand)

  • polyesterkwast 25mm rond, houten steel, ongelakt

    polyester brush 25mm round, wooden handle, unvarnished

    2,90 EUR (zzgl. 21% USt. zzgl. Versand)

  • houten polyesterkwast 35mm plat

    houten polyesterkwast 35mm plat

    1,83 EUR (zzgl. 21% USt. zzgl. Versand)

  • kwast plat 40mm, wooden handle, blank

    Brush, flat, 40mm, wooden handle.

    2,35 EUR (zzgl. 21% USt. zzgl. Versand)

  • houten polyesterkwast 50mm plat

    wooden polyester brush 50mm flat

    2,86 EUR (zzgl. 21% USt. zzgl. Versand)

  • Polyester kwast plat 75mm

    Polyester brush, Flat, 75 mm

    0,00 EUR (zzgl. 21% USt. zzgl. Versand)

Features

- Hardness: Shore A 50
- Elongation at Break: 400 %
- Tensile Strength: 18.2 N/mm
- Colour: Beige

Sicherheit

  • Glove Vinyl Large /box 100pcs

    Glove Vinyl Large/Box of 100 pcs.

    10,75 EUR (zzgl. 21% USt. zzgl. Versand)

  • Glove Vinyl Medium /box 100pcs

    Glove Vinyl Medium/Box of 100 pcs.

    10,75 EUR (zzgl. 21% USt. zzgl. Versand)

  • Glove Vinyl Small /box 100pcs

    Glove Vinyl Small/Box of 100 pcs.

    9,45 EUR (zzgl. 21% USt. zzgl. Versand)

  • Glove Vinyl X-Large /box 100pcs

    Handschoen Vinyl XL doos 100 stuks

    10,75 EUR (zzgl. 21% USt. zzgl. Versand)

  • Stenchmask carbon fibre

    Stenchmask carbon fibre

    5,60 EUR (zzgl. 21% USt. zzgl. Versand)

  • Supergloves Large Latex /box 100pcs

    Supergloves Large Latex box 100 pcs

    11,50 EUR (zzgl. 21% USt. zzgl. Versand)

  • Supergloves Latex small /box 100pcs

    Latex medical gloves, small, box of 100 pcs.

    11,50 EUR (zzgl. 21% USt. zzgl. Versand)

  • Supergloves Latex Medium /box 100pcs

    Latex medical gloves, medium, box of 100 pcs.

    11,50 EUR (zzgl. 21% USt. zzgl. Versand)

  • Supergloves Latex X-Large /box 100pcs

    Latex medical gloves, small, medium, large, xlarge, box of 100 pcs.

    11,50 EUR (zzgl. 21% USt. zzgl. Versand)

  • Filter ABEK1 for 3M 6200 maskers

    Protection against organic vapors, Inorganic and acid gases, Ammonia, and ammonia derivatives of

    19,45 EUR (zzgl. 21% USt. zzgl. Versand)

  • Nitrile Medical Examination Gloves Small / box 100

    The Supergloves Bluple nitrile disposable glove is made from top quality nitrile. The Bluple nitrile is, despite its smaller thickness (3.2 mil.), Strong and particularly comfortable due to its hig...

    10,50 EUR (zzgl. 21% USt. zzgl. Versand)

  • Nitrile Medical Examination Gloves Medium / box 10

    The Supergloves Bluple nitrile disposable glove is made from top quality nitrile. The Bluple nitrile is, despite its smaller thickness (3.2 mil.), Strong and particularly comfortable due to its hig...

    10,50 EUR (zzgl. 21% USt. zzgl. Versand)

  • Nitrile Medical Examination Gloves Large / box 100

    The Supergloves Bluple nitrile disposable glove is made from top quality nitrile. The Bluple nitrile is, despite its smaller thickness (3.2 mil.), Strong and particularly comfortable due to its hig...

    10,50 EUR (zzgl. 21% USt. zzgl. Versand)

  • Nitrile Medical Examination Gloves Extra Large / b

    The Supergloves Bluple nitrile disposable glove is made from top quality nitrile. The Bluple nitrile is, despite its smaller thickness (3.2 mil.), Strong and particularly comfortable due to its hig...

    10,50 EUR (zzgl. 21% USt. zzgl. Versand)

  • Paint spray mask Colad

    COLAD spray mask is a disposable mask with two active carbon cartridges that protect against the inhalation of organic solvents. The COLAD spray mask should be replaced after 40 hours by a new spra...

    29,25 EUR (zzgl. 21% USt. zzgl. Versand)

  • Paint spray mask - type 6200 - L

    halfgelaatmasker voor verfspuiten - type 6300 - la

    29,95 EUR (zzgl. 21% USt. zzgl. Versand)

  • Paint spray mask - type 6200 - M

    Comfortable and easy to wear paint spray mask. By making a minimum of components. Easy cleaning Due to the large surface area of the filters, a very low breathing resistance arises. The filters a...

    29,95 EUR (zzgl. 21% USt. zzgl. Versand)

  • Paint spray mask - type 6200 - S

    halfgelaatmasker voor verfspuiten - type 6100 - s

    31,08 EUR (zzgl. 21% USt. zzgl. Versand)

Products

  • Trennmittel
  • Mischen, Messen & Wiegen

You might also need...

  • Mixing Beakers
  • Measuring Cups & Jars
  • Weighting devices
  • Brushes
  • Protective Gear such as gloves
  • Release agents

Features

- Hardness: Shore A 60
- Elongation at Break: 480 %
- Tensile Strength: 24.3 N/mm
- Colour: Beige

Hilfe bei der Auswahl

Produkte nach Anwendung sortiert, z. B.:Lifecasting, Bildhauerei, Gießen, Special FX Make-up, Zahnprothesen Special FX, Studium.

Über uns Kontakt Transportoptionen Kundenprojekte Anwendungsbereich Marken Branches

Ihr One-Stop-Shop für 3D-Modelling-Materialien